Edimax ES-3132RL Manual do Utilizador

User Manual ES-5808PHG  Gigabit 8-Port 802.3at PoE Web Smart Switch

9 Figure 1-2 Configuration System System Configuration This page shows system configuration information. User can configure lots of information as F

10 Figure 1-3 ¾ MAC Address: Displays the unique hardware address assigned by manufacturer (default). ¾ S/W Version: Displays the switch’s firmware

11issued by the switch to specified trap managers. You must specify trap managers so that key events are reported by this switch to your management

12 Figure 1-4-1 Figure 1-4-2 VLAN A Virtual LAN (VLAN) is a logical network grouping that limits the broadcast domain, which would allow you to iso

13devices are still plugged into the same switch physically. Port Segmentation (VLAN) Configuration ¾ VLAN ID: ID of configured VLAN (1-4096, no l

14VLAN Per Port Configuration The 802.1Q Per Port Configuration page allows you to change the VLAN parameters for individual ports or trunks. You ca

15Only.” ¾ PVID: The PVID (Port VLAN ID) is associated with untagged, ingress packets. It is assigned to untagged frames received on the specified i

16LACP IEEE 802.3ad Link Aggregation Control Protocol (LACP) increases bandwidth by automatically aggregating several physical links together as a l

17configuration message (BPDU frame). Number between 1-10 (default is 2). ¾ Max Age – The maximum time (in seconds) a device can wait without receiv

18 Figure 1-8-2 Figure 1-8-3 Figure 1-8-4

IContent Content…………………………………………………………………………………I Introduction……………………………………………………………………………..3 Product Overview……………………………………………………………………………….3 Web M

19IGMP Snooping IGMP Snooping is the process of listening to IGMP network traffic. IGMP Snooping, as implied by the name, is a feature that allows

20Mirroring Port Mirroring is used on a network switch to send a copy of network packets seen on one switch port (or an entire VLAN) to a network mo

21 Figure 1-10-2 Quality of Service (QoS) In QoS Mode, select QoS Disabled, 802.1p, or DSCP to configure the related parameters. QoS Configuration ¾

22 Figure 1-11-1 QoS Mode: QoS Disabled When the QoS Mode is set to QoS Disabled, the following table is displayed. Figure 1-11-2 QoS Mode: 802.1p

23 Figure 1-11-3 Figure 1-11-4 QoS Mode: DSCP DSCP: Packets are prioritized using the DSCP (Differentiated Services Code Point) value. The Differen

24DSCP Configuration table to a common priority queue. Use Custom if you want to set each value individually. When the QoS Mode is set to DSCP, the

25PoE Configuration Remote access and monitor the attached PD (Powered Device) status by using Enable/Disable function. ¾ PoE Enabled: POE of the po

26 Figure 1-13-1 ¾ Enable Rate Limit: Click the check box to enable storm control. ¾ Rate (number of frames per second): The Rate field is set by a

27 Figure 2-1 Detailed Statics Figure 2-2 LACP Status LACP Aggregation Overview Figure 2-3-1

28¾ Port: The port number. ¾ Port Active: Shows if the port is a member of an active LACP group. ¾ Partner Port Number: A list of the ports attached

IIIGMP Snopping………………………………………………………………………….19 IGMP Configuration…………………………………………………………………19 Mirrioring…………………………………………………………………………………20 Moirrioring

29¾ Fwd Delay: The maximum time (in seconds) the root device will wait before changing states (i.e., discarding to learning to forwarding). This del

30¾ Protocol: Shows the spanning tree protocol functioning on this port, either RSTP or STP (that is, STP-compatible mode). IGMP Status IGMP Status

31 Figure 2-6-1 Figure 2-6-2 Figure 2-6-3

32 Figure 2-6-4 Ping This command sends ICMP echo request packets to another node on the network. Ping Parameters ¾ Target IP Address: IP address of

33 Figure 2-7-1 Figure 2-7-2

34 Figure 2-7-3 Maintenance Warm Restart Press Yes button to restart the switch, the reset will be complete when the power lights stop blinking. Fi

35Software upload Select “Upgrade Firmware” from the Tools drop-down list then click on the “Browse” button to select the firmware file. Click the A

36Reset button for the factory default setting Please take the following steps to reset the Web Smart Switch back to the original default: Step 1:

3Introduction Product Overview This switch is a Web Smart Switch equipped with 8-ports PoE+ 10/100/1000BaseT(X) plus 2-port gigabit SFP. It is des

4IGMP Status VeriPHY Ping ¾ Maintenance Warm Restart Factory Default Software Upload Configuration File Transfer Logout Specifications ¾ Standard I

5¾ Product Dimensions/ Weight: 440 × 220 × 44 mm (L x D x H ) / 3.2kg Performance ¾ MAC Address: 8K ¾ Buffer Memory: 176 KB ¾ Jumbo Frames: 9.6K ¾ T

6Hardware Description This part primarily presents hardware of this switch, physical dimensions and functional overview would be described. Physical

7 Rear Panel The 3-pronged power plug is placed at the rear panel of the switch right side shown as below. Hardware Installation Set the sw

8Software Description This part instructs user how to set up and manage the switch through the web user interface. Please follow the description to