Edimax 16 Port Nway Fast Ethernet PoE Web Smart Switch Manual do Utilizador

- 0 - 16 Port Nway Fast Ethernet PoE Web Smart Switch User’s Manual Ver:1.3.3

- 9 - Port Management: Port Configuration Select the “Port No.” - configure the mode below: 1. “Auto-Nego” - enable/disable Auto-Negotiation.

- 10 - Port Management: Port Mirroring Port Mirroring is used to mirror traffic, RX, TX or TX&RX, from Source port to Destination p

- 11 - Port Management: Bandwidth Control 1. Select the “Port No.”: you can choose port 1 to port 16 2. “TX Rate Value”: set the transmission r

- 12 - Port Management: Broadcast Storm Control 1. “Threshold” - Set the threshold from 1~63. 2. “Enable Port” - per port to define the status

- 13 - Port Management: PoE Configuration Remote access and monitor the attached PD (Powered Device) status by using Enable/Disable function. 1.

- 14 - VLAN Setting: VLAN Mode There are two VLAN modes : Port Based VLAN and Tagged VLAN. Click “Change VLAN mode” to select the mode. **If th

- 15 - VLAN Setting: VLAN Member Setting (Port Based) You can select a port group. 1. Click the port numbers: which you want to put th

- 16 - VLAN Setting: Multi to 2 Setting This is a special design for easily setting the switch VLAN into “VLAN Per Port“. 1. Choose

- 17 - Per Port Counter: Counter Category You can read the transmitting and receiving packet of the connecting port. Click “Refresh” or “Clear” t

- 18 - QoS Setting: Priority Mode There are three Priority Modes to select. 1. “First-in-First-Out” - the first receiving packet will be firstly

- 1 - Web Smart Switch Configure Please follow the steps to configure this Web Smart switch. Step 1: Use a twisted pair cable to connect this switc

- 19 - QoS Setting: Class of Service

- 20 - You can set QoS mode of per port by different bases. TCP/UDP > TP TPS/DS > 802.1P > Physical port 1. “TCP/UDP Port” – Q1 ~ Q4 opti

- 21 - Security: MAC Address Filter Set special MAC address to activate on the selected port 1. Choose “Select Port” – port 1~16 2. “Binding

- 22 - Security: TCP_UDP Filter Configuration You can enable or disable this function of per port. If the “Function Enable” is “Enable”,

- 23 - protocol will be dropped and other protocols will be forwarded. “Allow”: the selec

- 24 - Spanning Tree: STP Bridge Settings This setting is to avoid the loop network. 1. Select the “STP Mode”- choose “Disable”, “STP” or “RSTP”

- 25 - Spanning Tree: STP Port Settings 1. Choose “Port No.” : Port 1 ~ Port 16 2. Choose “Priority”: 0~ 240 3. “RPC” = Root Path Cost: 0 =

- 26 - Trunking: Link Aggregation Settings There are two groups to choose and max. for each group is 4 ports. Click “Submit” to confirm and fin

- 2 - Step 4: After the authentication procedure, the home page shows up. Select one of the configurations by clicking the icon. - Administrator -

- 3 - Administrator: Authentication Configuration 1. Change the user name and the password. 2. Click “Update” to confirm the new change.

- 4 - Administrator: System IP Configuration 1. Change the IP address: type the new IP address or select DHCP IP configuration.

- 5 - Administrator: System Status MAC address and system version will be shown on the screen. 1. Change the new comment of this switch

- 6 - Administrator: Load Default Setting 1. Click “Load” to back to the factory default setting. **Note: Recover switch default setting ex

- 7 - Administrator: Firmware Update Follow the instruction on the screen to update the new firmware. Please contact with your sales agent

- 8 - Administrator: Reboot Device 1. Click “Confirm” to reboot the device. Now, the setting of “Reboot Device” is finished.